產品描述

 [金鑲玉集團]scsi軟驅 TEAC FD-235HS 1211 Detailed Product Description

The TEAC FD235HS-1211 scsi floppy drive are made of two major components: the 3.5 floppy drive and the FC-1 host adapter.      　[金鑲玉集團]scsi軟驅 TEAC FD-235HS 1211 The FC-1 adapter provides the SCSI interface, single-ended, which has a standard 50-pin connector low density. 　[金鑲玉集團]scsi軟驅 TEAC FD-235HS 1211 The host adapter and the drives are proprietary technology of TEAC, and these floppy disk drives cannot be used as standard 3.5 1.44MB disk drives without the card.[金鑲玉集團]scsi軟驅 TEAC FD-235HS 1211

Product Warranty Information

　[金鑲玉集團]scsi軟驅 TEAC FD-235HS 1211

All TEAC models feature a 90-Days warranty from the date of purchase.

　[金鑲玉集團]scsi軟驅 TEAC FD-235HS 1211

Registration Information

　[金鑲玉集團]scsi軟驅 TEAC FD-235HS 1211

There is no need to register your product. TEAC provides 100% support for your product. You need, however, to keep your invoice in a safe place. The invoice is your proof of purchase and you will be required to send us a copy for repair and/or replacement.

　[金鑲玉集團]scsi軟驅 TEAC FD-235HS 1211

Parts, Replacement, and Repair Information

　[金鑲玉集團]scsi軟驅 TEAC FD-235HS 1211

Computer stores usually provide a 15 to 30-day warranty in most products. In case of a defective unit, contact your vendor immediately to have it replaced.

If your unit is out of warranty from the vendor, please contact our service department at xu@ruanqu.net for repair and/or replacement information, and have the following information ready:

1. Model name
2. Part number
3. Serial number
4. Invoice[金鑲玉集團]scsi軟驅 TEAC FD-235HS 1211

Identifying your floppy Drive  [金鑲玉集團]scsi軟驅 TEAC FD-235HS 1211

OEM production models are not listed in this knowledge base; you need to contact the manufacturer of the piece of equipment where your floppy drive was originally installed in order to receive information for repair, replacement, and availability.

1. All TEAC 3.5 floppy disk drives have the prefix TEAC FD235HS-1111 scsi floppy drive, which denotes the size of the disk: 3.5 drive.
   　[金鑲玉集團]scsi軟驅 TEAC FD-235HS 1211

2. The next two characters in the model nomenclature denote the density, and type of interface of the device:
   [金鑲玉集團]scsi軟驅 TEAC FD-235HS 1211
   HS: Dual Density: 720K and 1.44MB; the letter S denotes the SCSI interface.
   　[金鑲玉集團]scsi軟驅 TEAC FD-235HS 1211

3. The suffix denotes the series information:
   [金鑲玉集團]scsi軟驅 TEAC FD-235HS 1211
   FD235HS-1111
   FD235HS-1011
   FD235HS-911
   FD235HS-711
   　[金鑲玉集團]scsi軟驅 TEAC FD-235HS 1211
4. The color of the bezel for the TEAC FD235HS-1111 series remains the same. Please refer to thexu@ruanqu.net for details.

1. If your drive is not yet installed, you can identify it by its model label, which is located in the bottom side, towards the front side of the drive. Refer to figure A for details.

[金鑲玉集團]scsi軟驅 TEAC FD-235HS 1211
Figure A

1. The nameplate in the back of the drive does not indicate the model nor serial number in your drive. Always, refer to the label in the bottom side of the drive.
   　[金鑲玉集團]scsi軟驅 TEAC FD-235HS 1211
2. If your drive is already installed in your system, then you may find the model number in your invoice. Please keep your invoice in a safe place since this is your proof of purchase and you will be required to send us a copy for repair.

　[金鑲玉集團]scsi軟驅 TEAC FD-235HS 1211

Specifications

The following table provides a description of the hardware specifications for the SCSI interface 3.5 1.44MB floppy disk drive models TEAC FD235HS-1111x.

  [金鑲玉集團]scsi軟驅 TEAC FD-235HS 1211
　    

jumper information

1. The jumpers in the back of the drive provide normal floppy functions, SCSI termination, and the SCSI ID number. Refer to figure A for details.
   NOTE: Insertion of the plastic strap onto the post pin is defined as the on-state of the strap.

　

Figure A

[金鑲玉集團]scsi軟驅 TEAC FD-235HS 1211　

a.	SCSI ID Jumpers. ID 0 by factory default. All jumpers ON.
b.	Power connector
c.	Standard floppy function jumpers.
d.	330 Ohm terminator
e.	Standard 50-pin SCSI interface
f.	Floppy bridge (34 to 50-pin connection)
g.	Floppy label**

　

1. The jumpers in the bottom of the FC-1 host adapter provide the SCSI configuration. 
   By factory default, jumpers PAR, and H are set to ON. See figure B.

Figure B
　

1. Detailed function and description information of these jumpers is available from our catalog at:http://www.ruanqu.net
2. Figure C.A provides the default jumper configuration of normal floppy operation for model FD235HS711.
   　
3. Figure C.B provides the default jumper configuration of normal floppy operation for models 911, 1011, and 1111

Driver information

Although the TEAC FD235HS-1111 floppy drives have a standard SCSI interface, there are no drivers available from TEAC. You need to create your own drivers.


The process of development and implementation of software drivers is unique to each PC and NON-PC applications; and for that, the SCSI Command Set of Instructions is available at request to our Technical Support Department at DSPDTSG@TEAC.COM.
You are required to read, and sign our Non-Disclousure Agreement (NDA) and return it to us via fax: http://www.ruanqu.net . You should receive the manual upon approval.

installation

Introduction

The quality of the TEAC FD235HS-1111 drives provide a trouble-free operation for your computer system if properly installed. The following information will guide you thoroughly through an easy step-by-step method for a proper installation of your floppy disk drive.



Your TEAC FD235HS-1111 drive must be handled with care. Avoid applying undue force or abnormal strain to the spindle motor, stepping motor or printed circuit board assembly (PCBA).

It is best to hold the drive by the sides. Never loosen the fixing screws of the PCBA.


Preparing your system

CAUTION: TURN OFF YOUR COMPUTER AND UNPLUG IT FROM THE AC POWER SOURCE BEFORE INSTALLING THE TEAC FD235HS-1111. FAILURE TO DO SO MAY RESULT IN ELECTRIC SHOCK.



1.


Unplug your computer.

2.


Detach all peripheral devices from your computer, such as printer, keyboard, mouse, etc.

3.


Remove cover from your computer. Refer to your computer manual for this procedure.

4.


The floppy interface cable is the flat ribbon type, and the power connector consists of the 4 separate wires attached to a single connector.


Configuring the TEAC FD235HS-1111 Floppy Disk Drive

1.


If this is the only device connected to your SCSI card, then make sure termination is enabled; otherwise, you need to verify that the drive's SCSI ID # does not conflict with any of the other devices connected to the chain; if the drive is not connected at the end of the chain, then you need to disable termination as well.

2.


Use a standard 50-pin SCSI interface cable to complete the installation.

3.


Connect the TEAC FD235HS-1111 floppy disk drive to the 50-pin SCSI cable.
Installing the TEAC FD235HS-1111 Floppy Disk Drive

1.


Slide the drive into the available standard 1 high bay.

2.


Locate the SCSI cable, and connect the red or blue stripe into pin # 1 in the drive, which is located towards the power connector in the drive.

3.


Connect the power connector to the drive.

4.


Place the screws through each set of holes in the drive.

5.


Be sure to have a copy of the SCSI Command Set manual so you can create your own drivers to make the interface possible between the TEAC FD235HS-1111 and your SCSI application. Refer to the Driver Information section for details.

system integrator's resources

　

Developers / System Integrators Documentation

TEAC America provides the following documentation for those customers in the United States of America, who are integrating the TEAC FD235HS-1111 drives into their hardware application design.



1. The Hardware specification manual includes information such as:

Physical dimensions

Reliability information (MTBF)

Environmental conditions

Power Interface and connectors

SCSI hardware interface (Pinouts)

Electrical characteristics


2. The Software specification manual includes detailed information on the command set supported by the TEAC drive. 


3. Safety Agency Certificates may include UL, TUV, CE, CSA, etc.

　

 

 

 

 

 

隸屬分公司︰ 金鑲玉工業存儲

產品圖片